[Woodcarver] terminology explaination (was cutting angles)

[Merrilee Johnson]

Thanks for that explaination, Larry.  For some reason it never made sense 
and all of a sudden it did today! :) Goes to prove some days things sink in 
and others ...well just dont!  HAve a great week!
Merrilee

>From: "Larry Robertson" <workinginwood at hotmail.com>
>Reply-To: "[Woodcarver]" <woodcarver at six.pairlist.net>
>To: "[Woodcarver]" <woodcarver at six.pairlist.net>
>Subject: Re: [Woodcarver] terminology explaination (was cutting angles)
>Date: Sun, 17 Oct 2004 12:54:05 -0400
>
>To make a DONATION to the Mailing List using PayPal OR regular mail, click 
>this link: http://wwwoodcarver.com/WWWList/WWWList.html
>
>Hi Merrilee
>
>"Face Side" is a term we throw around in the furniture trade.  It means the 
>good side of the board(or the side which will be on the display on the 
>finished piece, for example a drawer front).  In Jean's case I assume the 
>face side will be the inside of the open book (open at 60 degrees - inside 
>measurement).  I use the face side ( pencil marked with an "F") to make 
>sure I'm always referencing measurements from the same side when cutting 
>joints.
>
>Larry Robertson
>Colchester, Ontario
>www.picturetrail.com/workinginwood
>----- Original Message ----- From: "Merrilee Johnson" 
><merrihat at hotmail.com>
>To: <woodcarver at six.pairlist.net>
>Sent: Sunday, October 17, 2004 12:41 PM
>Subject: Re: [Woodcarver] terminology explaination (was cutting angles)
>
>
>>To make a DONATION to the Mailing List using PayPal OR regular mail, click 
>>this link: http://wwwoodcarver.com/WWWList/WWWList.html
>>
>>Ok Larry,
>>Now I have a guestion - when I am sewing, the side of the fabric with the 
>>brightest color/print (shows on the outside), is called the right side of 
>>the fabric. This I understand but I have seen "put the boards with the 
>>face side down on the table" and wasn't sure what that meant exactly.  So 
>>to double check if I understand this - is that the side of the board you 
>>want your design on?  And as Jean said no laughing and pointing please :)
>>Thanks!
>>Merrilee
>>
>>
>>>From: "Larry Robertson" <workinginwood at hotmail.com>
>>>Reply-To: "[Woodcarver]" <woodcarver at six.pairlist.net>
>>>To: "[Woodcarver]" <woodcarver at six.pairlist.net>
>>>Subject: Re: [Woodcarver] Cutting  Angles
>>>Date: Sun, 17 Oct 2004 10:00:47 -0400
>>>
>>>To make a DONATION to the Mailing List using PayPal OR regular mail, 
>>>click this link: http://wwwoodcarver.com/WWWList/WWWList.html
>>>
>>>Hi Jean,
>>>If I understand what you are asking you have to set the bandsaw table at 
>>>15 degrees and rip both pieces with the face side down on the table.
>>>
>>>Larry Robertson
>>>Colchester, Ontario
>>>www.picturetrail.com/workinginwood
>>>----- Original Message ----- From: "Jean Athey" <atheyjm at yahoo.com>
>>>To: "Woodcarver MailList Submission" <woodcarver at six.pairlist.net>
>>>Sent: Saturday, October 16, 2004 5:53 PM
>>>Subject: [Woodcarver] Cutting Angles
>>>
>>>
>>>>To make a DONATION to the Mailing List using PayPal OR regular mail, 
>>>>click this link: http://wwwoodcarver.com/WWWList/WWWList.html
>>>>
>>>>Hello all,
>>>>I'm stumped at what should be an easy task, but I'm
>>>>new at marking and cutting angles. I've got two
>>>>12"x12" boards that are each 3/4" thick (1x12 stock.)
>>>>I want to stand these two boards on end and cut a
>>>>miter so that the two 12" sides form about a 60 degree
>>>>angle when glued together--as if you opened a book
>>>>that was 12" tall and set it on end with the two
>>>>covers fanning open to a 60 degree angle. I've tried
>>>>setting my bandsaw table at several angles, but can't
>>>>come up with the correct cut when the two  3/4" thick
>>>>boards are matched along the sides. If anyone
>>>>understands what I'm trying to achieve, please tell me
>>>>how to do it. And no pointing and laughing!
>>>>Jean
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>_______________________________________________
>>>>Woodcarver mailing list
>>>>Woodcarver at six.pairlist.net
>>>>http://six.pairlist.net/mailman/listinfo/woodcarver
>>>>
>>>_______________________________________________
>>>Woodcarver mailing list
>>>Woodcarver at six.pairlist.net
>>>http://six.pairlist.net/mailman/listinfo/woodcarver
>>
>>_________________________________________________________________
>>Don’t just search. Find. Check out the new MSN Search! 
>>http://search.msn.click-url.com/go/onm00200636ave/direct/01/
>>
>>_______________________________________________
>>Woodcarver mailing list
>>Woodcarver at six.pairlist.net
>>http://six.pairlist.net/mailman/listinfo/woodcarver
>>
>_______________________________________________
>Woodcarver mailing list
>Woodcarver at six.pairlist.net
>http://six.pairlist.net/mailman/listinfo/woodcarver

_________________________________________________________________
Check out Election 2004 for up-to-date election news, plus voter tools and 
more! http://special.msn.com/msn/election2004.armx